The permit application is assembled. The architectural and structural drawings are complete. The planning approvals are in hand. And then the building department sends a plan check comment: “Provide geotechnical report per CBC Section 1803.” The project stops while the developer figures out what this means, finds a geotechnical engineer, and waits for the investigation and report.
This is an entirely preventable delay. California’s geotechnical permitting requirements are well-defined and, once understood, can be integrated into the project planning process rather than encountered as surprises during plan check.
When a geotechnical report is submitted with a permit application, the plan check engineer reviews it for: adequacy of the investigation scope for the proposed project; correct identification of applicable seismic design parameters; appropriateness of recommended foundation type and bearing capacity; specific compliance with local amendment requirements; and any site-specific conditions requiring special measures. Reports prepared by engineers experienced in the specific jurisdiction’s requirements move through plan check more efficiently.
Geotechnical field observation during construction is typically a condition of permit approval. The geotechnical engineer must observe grading operations and certify that fill compaction meets specified requirements; inspect excavations to confirm foundation soils match assumed conditions; and submit a final geotechnical observation letter to the building department documenting compliance. The grading certification and foundation observation letter are typically required documents before the building department will issue a final inspection approval.
G3 SoilWorks has prepared geotechnical compliance reports for projects across more than 30 California jurisdictions, from small residential additions to large commercial developments.
While the CBC provides a baseline, California jurisdictions vary significantly in their specific geotechnical requirements. Los Angeles County requires expanded boring depths in hillside areas and has specific report format requirements. The City of Los Angeles has its own soils ordinance and requires plan check by the Department of Building and Safety’s Grading Division. Orange County requires specific data format for liquefaction evaluations. San Diego County has specific requirements for sites in mapped fault zones.
Engineers who have not prepared reports for a specific jurisdiction before frequently receive multiple rounds of plan check comments on items that are jurisdiction-specific rather than technical — delayed because the report didn’t follow the local format, not because the engineering was inadequate. G3 SoilWorks’ experience across more than 30 California jurisdictions means our reports are prepared to meet local requirements from the first submission, minimizing plan check cycles and schedule delays.
Once construction begins, the geotechnical engineer’s compliance role shifts from report preparation to field observation and documentation. California grading ordinances typically require that the geotechnical engineer observe grading operations to verify that: existing ground is properly prepared before fill placement; fill material is suitable for use as engineered fill; fill is placed in lifts not exceeding the thickness specified in the geotechnical report; and compaction testing results meet the minimum percent compaction specified. These observations and the compaction test data are summarized in periodic field observation reports and a final grading certification letter submitted to the building department when grading is complete.
Foundation observation requirements vary by jurisdiction but typically require the geotechnical engineer to visit the site before concrete is placed for footings or slabs, to verify that: excavation has reached the bearing stratum specified in the report; groundwater conditions are as anticipated; and the exposed bearing soils are consistent with the geotechnical report’s description and recommendations. The resulting foundation observation letter — sometimes called a “footing inspection letter” or “foundation certification” — is submitted to the building department and is required before the foundation inspection can be approved. Missing this step is a frequent cause of hold-ups at the final inspection phase.
When a geotechnical report fails plan check, the options are limited and the implications are significant. The plan checker may require: additional borings or test pits to provide data the original investigation did not address; additional laboratory tests that were not included in the original testing program; revisions to the engineering analysis or recommendations; or, in some cases, peer review by a second engineer at the applicant’s cost. Each of these outcomes adds time and cost to the project — and the new investigation or analysis generates a supplemental report that must go through another plan check cycle.
The most common reasons geotechnical reports fail California plan check are: insufficient boring depth to characterize the full profile relevant to the proposed structure; failure to address the specific local amendments adopted by the jurisdiction; liquefaction evaluation that does not follow the method required by the jurisdiction; and seismic design parameters that don’t match the current CBC edition in effect. G3 SoilWorks performs internal quality control review of every report before submission, checking the report against the specific requirements of the receiving jurisdiction to minimize the likelihood of preventable plan check failures.
The most efficient path through California’s geotechnical compliance process is the one that starts at the beginning of the project — not when a plan check comment arrives. Early geotechnical investigation informs design, aligns the report with the project’s actual scope, and prevents the costly iteration of designing first and then discovering that the foundation or grading must change to accommodate actual soil conditions.
Get a Compliance-Ready Geotechnical Report
GET A PROPOSAL FOR YOUR PROJECT
CBC Section 1803.3 requires a geotechnical investigation report when conditions exist that could adversely affect the structure’s performance. This encompasses most projects involving new construction, grading, or sites in seismic hazard or geologic study areas. The required report must be prepared by a California-licensed GE or CE with geotechnical specialty.
Practically speaking, yes for most projects. California grading ordinances typically require a soils report for grading projects exceeding threshold volumes, for sites on or near slopes, and for projects in geologic hazard zones.
In Los Angeles County, initial plan check review for geotechnical compliance typically takes three to eight weeks. Each response to plan check comments takes additional time. Overall timeline from first submission to permit issuance is commonly three to six months when geotechnical compliance is required.
A geotechnical field observation is a site visit by the engineer of record to observe and document that construction conforms to the geotechnical recommendations. It is typically required during grading, at key foundation stages, and at the completion of grading. The resulting observation letters are submitted to the building department as documentation of compliance.
Follow, engage, learn. Stop by our blog to see what’s happening at G3SoilWorks.
G3Soilworks – a full service geotechnical/ engineering geologic consulting firm serving clients since 2009 and delivering expert solutions with our highly experienced team and specialized consultants.
G3SoilWorks
350 Fischer Avenue Costa Mesa, CA 92626
Tel. 714.668.5600
E. info@g3soilworks.com